Dell Inspiron 8100, KOMPUTERY, DELL
[ Pobierz całość w formacie PDF ]
Dell© Inspiron© 8100: Removing and Replacing Parts Preparing to Work Inside the Computer NOTICE: Only a certified service technician should perform repairs on your computer. Damage or inoperability due to servicing not authorized by Dell is not covered by your warranty. NOTICE: Unless otherwise noted, each procedure in this manual assumes that a part can be replaced by performing the removal procedure in reverse order. NOTICE: To avoid damaging the computer, perform the following steps before you begin working inside the computer. 1 Make sure that the work surface is clean to prevent scratching the computer cover. 2 Save and close any open files, and exit any open programs. 3 Turn off the computer and all attached devices. HINT: Make sure the computer is turned off and not in standby or hibernate mode. If you cannot shut down the computer using the computerÔs operating system, press and hold the power button for 4 seconds. 4 Make sure the computer is undocked. 5 Disconnect the computer from the electrical outlet. 6 To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any attached devices. 7 Disconnect all other external cables from the computer. 8 Remove any installed PC Cards or plastic blanks from the PC Card slot. 9 Close the display and turn the computer upside down on a flat work surface. 10 Remove the primary battery from the battery bay and the secondary battery from the media bay, if a secondary battery is in use. NOTICE: To avoid damaging the system board, you must remove the main battery and secondary battery (if present) before you service the computer. 11 Remove any installed device in the media bay. 12 To dissipate any static electricity while you work, periodically touch an unpainted metal surface on the surface of the computer, such as the I/O panel on the back of the computer chassis. 13 Handle components and cards with care. Do not touch the components or contacts on a card. Hold a card by it edges or by its metal mounting bracket. Hold a component such as a microprocessor by its edges, not by its pins. Recommended Tools ¤ Number 1 magnetized Phillips screwdriver ¤ Small flat-blade screwdriver ¤ Pry stick ¤ Small plastic scribe ¤ Microprocessor extractor ¤ Flash BIOS update program floppy disk or CD (required only when upgrading the microprocessor, replacing the reserve battery, or replacing the system board). NOTICE: If the computer is running Microsoft§ Windows§ Millennium Edition (Me), you need to download the operating system update utility for Windows Me from http://support.dell.com and install it before you upgrade the BIOS. Screw Identification Before removing and replacing components, photocopy the screw placemat as a tool to lay out and keep track of the screws. The placemat provides the number of screws and the sizes. NOTICE: When reinstalling a screw, you must use a screw of the correct diameter and length. Make sure that the screw is properly aligned with its corresponding hole, and avoid over tightening. Screw Placemat Hard Drive Door Security : M3 x 5 mm (1 each) Keyboard to Bottom Case Assembly : M2.5 x 20 mm (4 each; plus one in memory module cover and one in Mini PCI card cover) Display to Base : M2.5 x 6 mm (3 each; 2 at back of computer; 1 at flex-cable strain relief) Display Bezel : Rubber screw covers (4 each) Plastic screw covers (2 each) M2.5 x 4 mm (6 each) Display Panel to Display Mounting Bracket : M2 x 3 mm (6 each) Video C ard : M2.5 x 8 mm (3 each) Flex-Cable Mounting Bracket to Top Cover : M2.5 x 4 mm (1 each) Palm Res t to Bottom Case Assembly : M2.5 x 20 mm (9 each) System Board : M2.5 x 4 mm captive washer (3 each) LED Board : M2 x 4 mm (2 each) Palm Res t Br ac ke t : M2.5 x 4 mm (2 each) M2.5 x 20 mm (1 each) Fan Assembly : M2 x 4 mm (3 each) RJ-11/RJ-45 Board Assembly : M2.5 x 4 mm (1 each) System Components display assembly keyboard hinge cover palm rest assembly thermal cooling assembly fixed optical drive system board storage module hard drive bottom case assembly main battery [ Pobierz całość w formacie PDF ] |